Installation de Debian Sarge sur Hp Pavillon zv5000ea (5112)

Forums ProgMatique
Programmation (C/C++, JAVA, PHP, JavaScript, ...) et Informatique (Webmaster, Web)
Retour au site Progmatique

FAQ

Rechercher

Forums ProgMatique Forum Index » Informatique en général » Linux / logiciels libres

Previous topic :: Next topic

Author

Message

Simon
Administrateur

Offline

Joined: 08 May 2005
Posts: 686

Localisation: France

Posted: Mon 13 Jun 2005 - 18:35 Post subject: Installation de Debian Sarge sur Hp Pavillon zv5000ea (5112)

Je configure en ce moment la distribution sur mon pc. Je posterai tres bientot le lspci. Si vous avez le meme pc, n'hésitez pas à poser des questions. _________________ Simon (SimMaster), Programmation et informatique Colorisation syntaxique de codes sources Outils et services autour de l'adresse IP

Simon
Administrateur

Offline

Joined: 08 May 2005
Posts: 686

Localisation: France

Posted: Mon 13 Jun 2005 - 21:08 Post subject: Installation de Debian Sarge sur Hp Pavillon zv5000ea (5112)

lspci -vv

Code:

0000:00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5833 (rev 02)
Subsystem: ATI Technologies Inc: Unknown device 1234
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at ea000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [a0] AGP version 3.0
   Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
   Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>

0000:00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5838 (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e8100000-e81fffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

0000:00:13.0 USB Controller: ATI Technologies Inc: Unknown device 4347 (rev 01) (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc: Unknown device 434c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8001000 (32-bit, non-prefetchable) [size=4K]

0000:00:13.1 USB Controller: ATI Technologies Inc: Unknown device 4348 (rev 01) (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc: Unknown device 434c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e8002000 (32-bit, non-prefetchable) [size=4K]

0000:00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 16)
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 8040 [size=16]
Region 1: Memory at 3c000000 (32-bit, non-prefetchable) [size=1K]

0000:00:14.1 IDE interface: ATI Technologies Inc: Unknown device 4349 (prog-if 8a [Master SecP PriP])
Subsystem: ATI Technologies Inc: Unknown device 4349
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 8060 [size=16]

0000:00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c
Subsystem: ATI Technologies Inc: Unknown device 434c
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

0000:00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=04, sec-latency=69
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: e8200000-e82fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-

0000:00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at e8003000 (32-bit, non-prefetchable) [size=256]

0000:00:14.6 Modem: ATI Technologies Inc: Unknown device 434d (rev 01) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at e8003400 (32-bit, non-prefetchable) [size=256]

0000:01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5835 (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e8100000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [58] AGP version 3.0
   Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit+ FW+ AGP3+ Rate=x4,x8
   Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:02.0 Network controller: Broadcom Corporation BCM4301 802.11b (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 12f3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e8200000 (32-bit, non-prefetchable) [size=8K]

0000:02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at e8204000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:04.0 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 3c001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
16-bit legacy interface ports at 0001

0000:02:04.1 CardBus bridge: Texas Instruments PCI1520 PC card Cardbus Controller (rev 01)
Subsystem: Hewlett-Packard Company: Unknown device 006b
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 3c002000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=0a, sec-latency=176
I/O window 0: 00000000-00000003
I/O window 1: 00000000-00000003
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite-
16-bit legacy interface ports at 0001

0000:02:07.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e8202000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:07.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at e8203000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:07.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 0x20 (128 bytes)
Interrupt: pin C routed to IRQ 11
Region 0: Memory at e8204400 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
   Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
   Status: D0 PME-Enable- DSel=0 DScale=0 PME-

_________________
Simon (SimMaster),
Programmation et informatique
Colorisation syntaxique de codes sources
Outils et services autour de l'adresse IP

Simon
Administrateur

Offline

Joined: 08 May 2005
Posts: 686

Localisation: France

Posted: Mon 12 Sep 2005 - 22:14 Post subject: Installation de Debian Sarge sur Hp Pavillon zv5000ea (5112)

Pour le modem interne (winmodem), j'ai arreté d'essayer de le faire fonctionner. Maintenant, j'ai l'adsl et le modem neufBox en ethernet. Au niveau de la configuration, il n'y rien a faire. _________________ Simon (SimMaster), Programmation et informatique Colorisation syntaxique de codes sources Outils et services autour de l'adresse IP

Display posts from previous:

	Forums ProgMatique Forum Index » Informatique en général » Linux / logiciels libres	All times are GMT + 2 Hours
Page 1 of 1